Valcom V-AW16A Specifications download pdf

Issue 8

1 947036

V-VCU

CLOCK CONTROLLER PACKAGE

GENERAL

The Valcom Clock Controller provides 24VDC power as

well as automatic synchronization and correction to

Valcom clocks when used with a V-DCPI Digital Clock

Protocol Interface, a V-D11025 2.5” Digital Clock, a V-

D11040 4.0” Digital Clock, a V-WMC Wireless Master

Clock Transceiver, a V-GPS GPS Receiver, a VERCA

Remote Card Adapter or a clock output from another

V-CCU.

PACKAGE INCLUDES

 1 Valcom V-CCU Clock Controller

 1 Valcom 24V Power Supply V-C6124P

 1 24V Wiring Harness

 1 6-Pin Silver-Satin Cord

 1 6-Pin RJ-11 Wiring Block

SPECIFICATIONS

Outputs

Three individual 2 Amp, 24VDC outputs are provided to

power up to 120 Valcom Analog clocks, 36 Valcom 2.5”

Digital Clocks or 30 Valcom 4.0” Digital Clocks.

Inputs

 Correction data

 24VDC input power

Features

 Supports two wire clock operation

 Individual current limited 2 Amp outputs

 User selectable correction intervals

 Data error LED indicators

 Power/Data output LED indicators

Dimensions/Weight

 2.63”H x 12.36”W x 7.75”D

(6.7cm H x 31.4cm W x 19.7cm D)

 7lbs. ( 3.2 kg ) (with power supply)

Power Requirements

The V-CCU requires 24VDC 2 Amps per output

(V-C6124P included).

Environmental

Operating Temperature: -0 to +40° C

Humidity: 0-95% non-precipitating

Wiring Requirements

 24AWG UTP, CAT 3/5/5E/6

INSTALLATION

Precautions

Failure to observe the following precautions could

result in damage to the V-CCU.

 Make all connections to the V-CCU and associated

equipment with the input power removed. Check

and verify all connections before applying power.

Note: Spare pairs in multi conductor talkback speaker

cables, as are often used for classrooms, may be used to

distribute Valcom 2-wire digital clock correction signals.

DO NOT use spare pairs in any cable being used to

provide line level audio to one-way speakers, amplifiers,

or local sound mixers (i.e. VE9121 type devices). For

other scenarios, contact tech support before using spare

pairs for 2-wire digital clock correction. In addition, it is

advisable to maintain 8 inches of separation between the

cable carrying 2-wire digital clock correction signals and

all other low voltage cables.

V-C6124P Mounting Instructions

 Locate an area on the wall capable of supporting the

weight of the power supply (approximately 5 pounds)

within six feet of an AC receptacle.

 Using the mounting bracket as a template, mark the

two slotted holes on the mounting surface.

 Using the two #8 screws enclosed, mount the

bracket to the mounting surface as shown

(See Figure 1).

 Slide the V-C6124P onto the mounting bracket.

V-C6124P Wiring Instruction



Plug the AC cord into the V-C6124P only.

(Do NOT plug into the AC outlet)

 Plug the wiring harness packaged with the

V-CCU into the output connector of the

V-C6124P (See Figure 1).

1 2 3 4

Summary of Contents

Page 1 - CLOCK CONTROLLER PACKAGE

Issue 8 1 947036 V-VCU CLOCK CONTROLLER PACKAGE GENERAL The Valcom Clock Con

Page 2 - V-CCU Wiring

947036 2V-CCU Mounting  Plug the 24V wiring harness from the V-C612

Page 3 - Master/Slave Mode

947036 3Setup and Programming  If using a V-GPS, a V-WMC or a V-D11

Page 4

947036 4 TECHNICAL SUPPORT When trouble is reported

Comments to this Manuals

No comments

Valcom V-AW16A Specifications

Browse online or download Specifications for Wall clocks Valcom V-AW16A. Valcom V-AW16A Specifications User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Wall clocks Valcom V-AW16A